RepRap/Configs/Slic3r/larsan-old.ini
- generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012
acceleration = 0 bed_size = 180,200 bed_temperature = 50 bottom_solid_layers = 3 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = cooling = disable_fan_first_layers = 1 duplicate = 1 duplicate_distance = 6 duplicate_grid = 1,1 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors external_perimeter_speed = 40% extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 30 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_diameter = 1.75 fill_angle = 0 fill_density = 0.15 fill_pattern = honeycomb first_layer_bed_temperature = 50 first_layer_extrusion_width = 0 first_layer_height = 0.27 first_layer_speed = 15% first_layer_temperature = 195 g0 = 0 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 50 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_speed = 60 layer_gcode = layer_height = 0.24 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 5 min_skirt_length = 0 notes = larsanconfig nozzle_diameter = 0.35 only_retract_when_crossing_perimeters = output_filename_format = [input_filename_base].gcode perimeter_acceleration = 25 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 50 perimeters = 3 post_process = print_center = 90,100 randomize_start = 1 retract_before_travel = 5 retract_length = 2 retract_length_toolchange = 3 retract_lift = 0 retract_restart_extra = 0.01 retract_restart_extra_toolchange = 0 retract_speed = 50 rotate = 0 scale = 1 skirt_distance = 20 skirt_height = 1 skirts = 3 slowdown_below_layer_time = 50 small_perimeter_speed = 100% solid_fill_pattern = rectilinear solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_speed = 90% start_gcode = G28 ; home all axes\nM92 E820 support_material = support_material_angle = 45 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_pattern = rectilinear support_material_spacing = 2 support_material_speed = 60 support_material_threshold = 41 temperature = 185 threads = 2 top_solid_infill_speed = 70% top_solid_layers = 3 travel_speed = 50 use_relative_e_distances = 0 vibration_limit = 0 z_offset = 0
